How to Install Touchless Kitchen Faucet

In the case of an active chef, the benefits of a touch-activated faucet would be readily obvious. Imagine that the palms are coated in pizza dough or coloring. You ought to wipe up, so that requires scattering the mess around the faucets. On a touch-activated faucet, you may use your thumb, elbow, or one remaining clean finger to easily press the faucet anywhere on the beam or handle that flips on the water without making a mess. Here are some steps to follow to Install Touchless Kitchen Faucet.

While cooking raw chicken or other food that contains potentially dangerous bacteria, the touch-activated faucet decreases the risk of cross-contamination from dirty hands or contaminated faucet handles, creating a cleaner, healthier food prep environment.

Install Touchless Kitchen Faucet

Kitchen faucets are one of the most unclean places in your house. Dirty hands flip on the faucet — right after touching fresh beef or cookie dough — and transfer the germs to the handles. And if you do not clean your faucet for every use, the filth builds up.

Remove the bacteria for good by adding a touchless kitchen faucet. The system is triggered such that your hand’s gestures are registered and automatically turned on when you need to wash. It is a win-win situation: save time and water — all while improving your wellbeing! Besides, the touchless socket is very easy to connect.

Touch-activated sockets often shut off with a single touch of the fingertips, allowing the consumer flexibility to concentrate on activities such as washing a bowl. To switch the water back for rinsing, a quick tap reactivates the same amount and temperature of the water you previously.

The valve/handle assembly that has three tubes: the hot and cold water lines of the valve, as well as the shorter valve outlet that interfaces with the solenoid.
Below you will find a properly organized guide on how you can install a touchless faucet in your kitchen.

Configuration of the Faucet

The design directions described here are unique to the top-mounting cast iron sink, but the Pilar faucet may also use in an under-mounting configuration or on thin stainless steel sinks by means of a stabilizer plate that comes with the faucet pack. Please adhere to the manufacturer’s directions regarding your specific circumstances. Turn off the touchless feature before Install Touchless Kitchen Faucet.

Step 1

First, connect the bolt by connecting the gasket to the end of the hammer, installing the end into the bolt hole, and locking the bolt with the insulating disk and the fixing pin, which screws over the bolt. Make sure that the light at the bottom of the beam base — which means that the electricity is alive on the solenoid — is pointing upward. Tighten the beam to the sink by cinching a pair of jack screws in the fixing nut.

Step 2

Next, mount the valve assembly, which contains the handle and three tubes: hot and cold water pipes, as well as the valve outlet which is attached to the solenoid. Slip the gasket onto the base of the valve/handle, then slip all the tubing down into the pit of the drain. The bottom of the valve/handle includes a long bolt extending down from the handle to which the crescent-shaped bracket fits. Its crescent form offers space to the three tubes. The bracket is fixed to the bolt by means of a special deep-well wrench included in the gripple pack. Note: If the mounting surface is rough or irregular, you can need to apply a bead of silicone sealant underneath the gasket.

The solenoid assembly slips from beneath the sink to the valve outlet (a narrow line hangs from the valve assembly). Be sure the tubing securely connects to the solenoid mouth and hold it in place with a tiny metal retaining clip placed into a few thin holes on the solenoid inlet.

Step 3

Lastly, mount the pull-down hose, which allows the customer the ability to expand the width of the water spray to reach the entire length of the sink. When achieving so, place the plastic hose guide at the end of the pipe, which is used as a convex nose when preventing snags while feeding the pipe into the metal conduit. Even with the hose guide, it took a little patience and a few attempts to successfully guide the hose all the way out of the bottom of the hose without catching an obstruction. If completed, cut the hose guide and attach it to the bottom of the solenoid with the special cylindrical film.

All Connections

With the major components installed, it’s time to wire everything up. Next, attach the wire on the solenoid assembly to the metal shank of the spout — it literally clamps onto the base with a circular film. Next, remove the plastic cap from the wire dangling from the shank (leading to the on / off control light on the spout). Link the shank wire to the related wire originating from the solenoid. No tools are required; the wires attach with a quick snap-together link.

Then, install the battery box by applying a pair of adhesive Velcro strings. The maker suggests placing the box as low to the floor as practicable. Link the remaining wire from the solenoid to the battery plate. I know that in print, all these wiring links can sound complicated, but they both have specific styles of wires, and there’s no chance of misunderstanding one wire with another. It is really easy, honestly. It is necessary to connect the test valves between your home supply stop valves and the hot and cold lines of the new socket.

Checking Pipes Links

Another significant distinction between the Delta Pilar touch-op faucet and the regular faucet is the addition of two tiny control valves. That must mount between the hot and cold water lines of the faucet and the shut-off valves of your home. These two-part components include a small ferrule that inserts into the supply stops. Followed by a slightly larger control valve that screws over the ferrule. Make sure that all fittings and contacts are clean of contaminants. Then simply screw the water lines of the socket over the ends of the control valves. Hand-secure both links, then secure the additional turn with the wrench — but do not over-tighten it.

Installation of soap dispenser

The current Delta jack mounts on a sink with three holes. But it only takes two holes to hold the jack and the valve/handle assembly. Of this purpose, we select a configuration that contains a soap dispenser to cover the third void. It essentially places a pump and a gasket above the sink. That is inserted through the body under the sink holding the sink. No wires or further connections for the soap dispenser. It provides a convenient place to keep the detergent and gives the entire facility a finished look. Eventually, turn the sprayer head and test all ties for leakage.

Finally, Configure and use of the sprayer

Place the batteries in the battery box and switch the gripple wide open on both hot and cold lines to clear out any debris. Instead, take the hose assembly out of the board and lock it into the sprayer handle. Inspect all ties for leakage, and the new jack will be ready for service.